Kettler 7136-000-500 User Manual

Match 5.0 Table Tennis Table Models 7136-000-500 & 7176-000-090-500Printed on recycled paper.Made in GermanyPicture SimilarKETTLER®International

Step 4 AssemblyInstall locking wheels.The grooves of wheels should face inward.Again, do not over torque; wheels should roll smoothly.Push down foot l

AssemblyStep 5 Paying attention to position of wheelbase, snap alignmentstruts into place.Bolt locking struts to base. Bolt the locking strut withthum

AssemblyStep 6Bolt one M8 crossbar between each wheelbase. Thiscrossbar is being assembled temporarily to create asupport base and will be removed at

AssemblyStep 7Insert endcap into the bottom of netpost bar.Using M6 crossbar, assemble crossbar and netpost barsto alignment struts.The netpost bar in

AssemblyStep 8Screw eyelets to four Jbars.Assemble safety levers to two of the Jbars.Slide handgrip onto safety lever.Note the orientation of the slot

AssemblyStep 9Screw eyelets to support leg on table-top half.Repeat for second table-top half.4 RequiredA B C4 Required3.9x13Support Leg15

A B CDStep 10Important: have two people complete steps 10-12. With assistance, lift onetable top onto the wheelbase; the legs will be facing outward.

A B CDStep 11Raise safety lever up straight. Bolt the safety lever to leg. Bolt the Jbars to leg.Insert footcaps.E FAssembly1 Requiredm6x372 Requiredd

Step 11 continuedAssemblyJ KLLegStep 12Bolt locking struts to support leg.AB C DE FG2 Requiredm6x492 Requiredm64 Requiredm12x618Now, remove the tempor

Assembly19A BCDTo properly open table into playing position: lock wheels (H), push thethumb latch down on the left locking strut. Squeeze the strut on

Note on SafetyAll KETTLER®products are designed in accordance with the latest safety regulations and undergo a constant process of qualitycontrol duri

A CDStep 13Slide net post onto netpost bar and screw into place. Insert guide plug.Repeat on other side of table.Assembly2 Required4.8x252 RequiredA B

A BStep 15Screw sideshroud into place.Repeat installation of second shroud on opposite sidewheelbase assembly.Assembly6 Required3.9x25213 Screws

AssemblyNet AssemblyNet assembly:Slide Jpin through net.. Place Jpin in designated slots. Tiestring to tension tab. Place string in slots over Jpin an

Assembly23Folding TableFolding Table:To properly fold the table, lock the wheels, press the safetylever up and lift top. Once the top is halfway up yo

THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, MADE BY EITHER THE DISTRIBUTOR OR THEMANUFACTURER ON KETTLER®PRODUCTS, EXCEPT THE MANUFACTURER’S LIMITE

25Ordering Spare PartsWhen ordering spare parts, always state the full model number, spare part number, the quantity required and the serial number.Ex

12125131744723232522810111929283032271520213125121253333131765237239373426353638Spare Parts26

Spare Parts1 Top 2 94130117 941301252 Leg 2 94111138 941111293 Footcap 4 70130540 701305404 Clamp (outdoor table) 8 101280285 Clamp 25mm (indoor table

KETTLER®International Inc., 1355 London Bridge Road, Virginia Beach, VA 23453 USAwww.kettlerusa.com • E-mail: [email protected] parts/service: ca

Before Assembly (continued)General Assembly Instructions• The equipment must be assembled with care by twoadults.• Separate all the parts including th

Items below are shown at actual sizeNumber Incl. - 1-6mm, 2-8mm Number Incl. - 2 (outdoor only) Number Included - 2 Number Included - 2Number Included

Package Contents (continued)Items below are shown at actual sizeNumber Included - 18m6Number Included - 2Number Included - 8m8Number Included - 8Numbe

AssemblyBegin the assembly of your table by carefully removingthe plastic wrap and all of the loose contents. Separatethe two table tops by removing t

AssemblyStep 2A B CD E F4 Required4 Requiredm88 Requireddia 16x84 Requiredm8x1254 Requireddia 25x88 RequiredEnd view and perspective view4 RequiredPay

J K LAssemblyStep 2 (continued)G H IPhoto K shows the non locking stemtube beinginstalled. Step E to step J are the same for the lockingand non lockin

Step 3 AssemblyInstall non-locking wheels.Do not over torque; wheels should roll smoothly.Install non-locking wheels on both wheelbaseassemblies.A B C